Skip to content

SIDs

SIDs are often the more difficult procedure to model in the dataset, as they often have a lot of variables associated with them, such as aircraft performance based turns; and differing ARINC leg types such as course to fix and altitude to fix.

Hello

When translating procedures, it is often better to translate them as it they were for the average aircraft. For example, in a performance-influenced departure like the ECHO5 out of Palmerston North, a prop will make a more drastic turn at a lower speed when compared to a faster jet aircraft.

Editor

The SID Screen

SID Screen

The above image shows the screen for a fully populated procedure. The screen is well annotated within the app, although there are a few key things to know about the behaviour of the app -

  • Changing the Runway will update all transitions for that procedure.
  • Changing the Name will update all transitions for that procedure.
  • Changing the Number will update all alphas and transitions for that procedure.
  • Changing the Alpha will update all transitions for that procedure.
  • Changing the Transition will update only the selected procedure.

The aircraft type box will alter what aircraft this SID can be made available to in the vatSys FDRs. Ticking the Radar SID box will make the SID the default for non-RNP/RNAV aircraft. Ticking the Default SID box will make it the default SID assigned to traffic for that runway.

The Delete this Procedure button will delete the individual procedure selected. If you have a transition selected, it will only delete that transition. The Delete every Procedure with this name button will delete every procedure with the same Procedure Name - regardless of whether or not it is on the same runway or not.

The two boxes below are the fix boxes. The procedures should flow from top to bottom in the order that they should be flown. The box on the left is the 'base procedure'

Add New Procedure

SID Screen

Adding a new procedure is relatively simple - you select the runway applicable, and fill out the other respective fields.

You can add a SID for either a single runway, or all runways at an aerodrome. Where a procedure might be for multiple but not all runways, you should select all.

Tip

When adding a procedure that has various transitions, you are required to add the base procedure first. This is the part of the procedure that is common to all of the transitions. Usually on charts, this is solid line portion of the procedure.

Subsequent transitions can be added by adding a new procedure, entering the base procedure, and then adding the desired transition fix in the Transition box. Clicking Add SID will open to the main screen, where you can add the transition route to the right hand text box.

Tip

You can also add custom coordinates to create a custom path, or a manual turning point. This is often used for a 500ft turn point, as can be seen in the above illustration of the ECHO5 procedure out of Palmerston North.

You can create this point by looking at the procedure in LittleNavMap, displaying the procedure and placing a custom waypoint where the turn commences. This coordinate can then be converted in the SFG's DMS Conv utility to the SCT format, and can be added like any other fix.

Populated SID Screen

The example above shows the RUXOX4S for Runway 07 at Palmerston North.

  • The PM25T and PM07T fixes are threshold fixes. Normally the opposite end threshold fix is not required, but has been added here, as VEPUR is slightly offset from the runway centreline.
  • RUXOX is the final common fix for the procedure.
  • Waypoints OLMUX, OH VOR and RUGVI make up the rest of the transition, and are entered in the order that they are flown.
  • The circle next to OH VOR designated that it is a ground-based navigation aid, not an IFR waypoint. VOR/DMEs and NDBs all show as a circle.

Warning

Modifying the base procedure while a Transition is selected will update the base procedure for all transitions.

Information

The IF, IAF, Fly over and FAF buttons are not applicable for SIDs.

Modifying a Procedure

Procedures can be modified by finding the procedure in the main window, and then modifying the respective data. The data will save if you attempt to navigate away from the procedure by either closing the window or select another procedure.